EPAK2500 - Control of Your ES System

EPAK2500 – Control of Your ES System

The EPAK2500 is a four-way, active control and amplification unit specifically designed for the ES Series modular loudspeaker system. It not only houses all signal processing and four individual amplifiers but also controls the allocation of power depending on the number of bass modules employed. The EPAK2500 is enclosed in a road-rugged case with side handles and a built in cable storage compartment. Easily transported on a trolley this unique amplification system has its electronics mounted on an independent suspension system that isolates it from the shocks and impacts typically encountered on the road. A large aluminum heat sink provides passive cooling along with two demand-sensitive fans for added reliability.

Categorie: ,
Descrizione

Features

  • 4-way modular, 2500W Control and Amplification system for use specifically with ES Series modules
  • High Frequency, 100W, Class AB, push-pull, low intermodulation amplifier with transformer balanced outputs
  • Mid Frequency, 200W, Class AB, push-pull, low intermodulation amplifier with transformer balanced outputs
  • Mid Bass, 600W, high efficiency, current enhancing, switching amplifier Subwoofer, 1600W, high efficiency, current enhancing, switching amplifier
  • Complete on board speaker management system including equalization, time alignment, crossover filters, amplifier overdrive protection, system set-up and output level controls
  • 20MHz sampling for on board time alignment and phase correction
  • AC soft start circuitry with ON/OFF AC breaker switch provides thorough power protection
  • Passive heat dissipation design with demand-sensitive forced cooling back-up system
  • Set-up provides selection and control of different subwoofer combinations
  • Professional enclosure using road-rugged case with side handles
  • Removable front cover provides storage of all AC and speaker cables
  • Bass Character- Attack or extension switch alters the low frequency character
  • Includes all speaker cables for a single stack ES system –

    High Frequency Amplifier Specification

    Type Class AB Push-Pull low inter-modulation Mosfet design with transformer balanced output
    Rated Continuous Power 100W
    Distortion <0.05%
    Operating Bandwidth 2.5kHz to 28kHz

    Mid Frequency Amplifier Specification

    Type Class AB Push-Pull low inter-modulation Mosfet design with transformer balanced output
    Rated Continuous Power 200W
    Distortion <0.05%
    Operating Bandwidth 500Hz to 2.5kHz

    Mid-Bass Frequency Amplifier Specification

    Type High efficiency, Low frequency, Current-enhancing switch mode
    Rated Continuous Power 600W
    Distortion <0.05%
    Operating Bandwidth 130Hz to 500Hz

    Low Frequency Amplifier Specification

    Type High efficiency, Low frequency, Current-enhancing switch mode
    Rated Continuous Power 1600W
    Distortion <0.05%
    Operating Bandwidth 20Hz to 130Hz

    Signal Input

    Input Sensitivity 1.0V RMS
    Input Impedance 20kΩ (balanced)

    Speaker Output

    Speaker Output AP6 (Mid-Hi), AP4 (Sub)

    Power Requirements

    Power Connector Neutrik PowerCon®
    Operating Voltage Range 100 to 120V@60Hz | 205 to 240V@50Hz | 225 to 260V@50Hz
    Recommended Amperage 20A 115V | 10A 230V | 10A 250V

    Physical Dimensions

    Height 719 mm (28.30″)
    Width 478 mm (18.82″)
    Depth 305 mm (12″)
    Weight 32 kg (70.4lbs)
DATA SHEET
USER MANUAL
DRAWINGS
VIDEOS & MEDIA
Recensioni (0)

Recensioni

Ancora non ci sono recensioni.

Recensisci per primo “EPAK2500 – Control of Your ES System”

Il tuo indirizzo email non sarà pubblicato. I campi obbligatori sono contrassegnati *